The Complete Guide to Cleaning Exposed Aggregate Driveways
Exposed aggregate driveways are durable and attractive, but their textured finish can trap dirt, leaf tannins, oil and organic growth. On Sydney’s North Shore, shade from established trees and damp conditions can encourage algae, particularly on south-facing driveways and areas with poor drainage.
The safest cleaning approach combines the right detergent, gentle agitation and controlled rinsing. Excessive pressure or unsuitable chemicals can damage the cement around the stones, affect sealers and leave permanent marks.

Understand Your Driveway Before Cleaning
Exposed aggregate consists of decorative stones embedded in concrete, with the surface cement removed to reveal their texture. Although the stones are hard-wearing, the surrounding cement paste and any protective sealer require care.
Before cleaning, check for loose stones, cracks, flaking sealer and areas where the concrete is crumbling. Cleaning will not repair these defects, and pressure washing can make them worse. If the driveway is newly installed, follow the installer’s curing and cleaning instructions before using detergents or pressure equipment.
Check Whether the Surface Is Sealed
A sealed driveway may have a sheen or repel water, although neither is a definitive test. Look for installation records or ask the contractor which product was applied. Knowing the sealer type helps you choose compatible cleaners and avoid patchy discolouration.
Equipment and Products You Need
- A stiff nylon broom or scrubbing brush; avoid wire brushes that can scratch surfaces or leave rust-producing fragments.
- A pH-neutral or manufacturer-approved concrete cleaner suitable for the driveway’s sealer.
- A hose with a trigger nozzle, or an adjustable pressure washer with a wide fan nozzle.
- Gloves, enclosed non-slip footwear and eye protection appropriate to the cleaner’s label.
- Drain covers, containment barriers and suitable recovery equipment where needed to prevent dirty water entering stormwater.
How to Clean an Exposed Aggregate Driveway
- Clear and inspect the area. Move vehicles and pots, sweep up leaves and grit, and identify damaged sections. Locate nearby stormwater pits before introducing water.
- Plan runoff control. Contain wash water and collect sediment. Do not direct detergent, oil, chemicals or dirty wash water into gutters or stormwater drains. Arrange a lawful disposal method before starting.
- Test a small section. Choose an inconspicuous spot to check the cleaner, dilution and washing method. Let it dry so you can assess colour and sealer changes.
- Apply cleaner as directed. Work in manageable sections on a cool surface. Follow the labelled dilution and dwell time, and do not let the solution dry.
- Scrub gently. Use a nylon brush to loosen dirt between the stones, paying attention to shaded edges and tyre tracks.
- Rinse with control. Start with a hose where practical. If pressure washing is necessary, begin at the lowest effective setting with a wide fan spray, keep the nozzle moving and maintain a generous distance from the surface.
- Inspect after drying. Check for remaining stains, slippery patches or surface damage before deciding whether another targeted treatment is necessary.
Removing Common Driveway Stains
Oil and Grease
Absorb fresh spills promptly with a suitable absorbent material, then collect it for appropriate disposal. Treat residue with a concrete-compatible degreaser, following its instructions. Older oil may penetrate deeply and need repeated treatment or a specialist poultice. Pressure washing alone often leaves a visible stain.
Algae and Other Organic Growth
Use a product specifically labelled for removing organic growth from concrete and compatible with the sealer. Protect nearby plants and prevent chemical runoff. Never mix bleach-based products with acids, ammonia or other cleaners. Improving drainage and removing accumulated leaves helps slow regrowth.
Leaf Tannins and Rust
Leaf stains and rust require different treatments, so use a stain-specific product approved for the surface. Avoid experimenting with hydrochloric acid: it can etch cement, alter the finish and damage some decorative stones. Persistent rust or unknown staining is a good reason to seek professional advice.
Pressure Washing Without Damaging the Surface
There is no single safe pressure setting for every exposed aggregate driveway. Surface age, condition, sealer and equipment all affect the result. Avoid narrow jets and turbo nozzles unless a qualified operator has assessed their suitability. Never concentrate the spray on cracks, loose aggregate or deteriorating cement.
A surface-cleaning attachment can improve consistency on suitable concrete, but it is not automatically damage-free. Incorrect pressure, nozzle selection or operating speed can still produce striping and erosion.
Managing Runoff on Sydney’s North Shore
Stormwater from North Shore properties can flow into local creeks, Sydney Harbour and surrounding waterways. Under NSW pollution laws, allowing polluted wash water to enter waterways can be an offence. Keep contaminated runoff out of stormwater, even when a cleaner is described as biodegradable.

Check current Sydney Water restrictions or Water Wise Guidelines before starting, as permitted outdoor water use can change. Ask your local council or relevant water authority about disposal requirements; sewer disposal may require approval and should never be assumed acceptable.
Should You Reseal After Cleaning?
Not every clean requires resealing. Consider it when the existing coating has worn away or the installer recommends maintenance. The surface must be clean and sufficiently dry for the selected product, and any existing coating must be compatible.
Choose a sealer suited to vehicle traffic and exposed aggregate. Discuss slip resistance, particularly on steep North Shore driveways: some film-forming finishes become slippery when wet. Follow the manufacturer’s weather conditions, application rates and curing times before allowing foot or vehicle traffic.

Keeping Your Driveway Cleaner for Longer
Sweep regularly, remove fallen leaves before they break down and address oil leaks promptly. Check shaded areas for slippery growth and keep drainage channels clear. Inspect the driveway every few months and clean according to its condition rather than relying on a https://kylerlbla903.silverstonebrief.com/posts/commercial-pressure-cleaning-standards-for-sydney-venues fixed schedule.
For steep access, extensive staining, loose aggregate or uncertain sealer compatibility, use a professional exposed aggregate driveway cleaning service on Sydney’s North Shore. Ask how they assess surface condition, control washing pressure and capture contaminated runoff—not simply how powerful their equipment is.
North Shore Pressure Cleaning Pros
(02) 9538 7942
Ends · EMILIANOTDDP710